High angle conveying from open pits isn’t new, just ignored

0
402
Developed copper mine pit with primary ore crusher at lower left and conveyor system leading to the processing plant at the upper left. Waste rock is spoiled into the valley behind the pit.

Various articles that announce high angle conveying from open pits as “innovative”, “next phase” and “new”, prove that not enough people in the industry are doing their research.  This cost efficient method of conveying has been proven and available for over 30 years and remains ignored by the IPCC (in-pit crushing and conveying) equipment and systems providers.  For a company like Dos Santos International, it is increasingly frustrating to see these articles make their way to publications as a new technology, when President and owner, Joseph Dos Santos has offered this option throughout his career.  Joe is the inventor of the DSI Sandwich Belt High Angle Conveyor and has researched and spoken regularly on the subject of high angle conveying, and how it offers the vital and missing link to optimized IPCC systems.

Reduced energy consumption and environmental impact, with IPCC systems, was already realized in the 1970’s.  With bulk material haulage limited to conventional open trough conveyors, this precluded the  most direct path out of the open pit, requiring low angle spiral ramps and/or deep slots and/or tunnels through the pit high wall.  These excavations, to accommodate the low angle limitations, represented undesirable impact on cost and on the environment increasing the amount of environmental disturbance for the amount of ore recovered.  Against this backdrop, a major study in 1979 sought to develop high angle conveying systems that could continuously haul the mined bulk material directly out of the pit, along the high wall, “the shortest distance between the two end points.”  Between 1979 and 1982 that study developed sandwich belt high angle conveying systems that utilized all conventional conveyor equipment, including smooth surfaced rubber belts that could be continuously scraped clean.  These systems had all of the positive features of conventional conveyors, but overcame the angle limitation.  By hugging the bulk material between two belts, the material’s internal friction could be developed to facilitate conveying at any high angle up to 90° (vertical).

After an intense testing period (about 1 year) on the first large scale prototype system, commercialization began in 1983 with the installation of a 60° incline system at a western USA coal mine, elevating 2000 t/h of coal to a train load out system.  It did not take a long period of scrutiny and acceptance before this high angle conveyor found use in the most rugged requirements of an IPCC system.  This was only the second commercial sale, and after more than 150 commercial installations, it remains arguably the most significant high conveying system.

In this case, a copper mine, already using pit perimeter crushing and conveying, decided to move their primary crusher deep into the pit and use a sandwich belt high angle conveying system to elevate the ore continuously, directly out of the pit, along the high wall to the pit perimeter where it then transferred to a conventional conveyor for the remaining haul to the plant.  The system had significant features including 2000mm wide belts that elevated 250mm coarse ore, at 4000 t/h, over six 15 meter high benches for a total of 90 meters of lift.  The system was able to reduce the truck haulage fleet by 10, 200 ton trucks realizing great cost savings, zero emission to the air, and greatly reduced traffic congestion in the pit.  They system operated successfully until 2002 when the mine shut down.

Suitability of the Sandwich Belt High Angle Conveyor

Suitability for IPCC systems has been demonstrated at all Dos Santos sandwich belt high angle conveyors with a number of units handling very large ore and rock at very high rates.

The most common concerns regarding sandwich belt high angle conveyor suitability for IPCC applications:

  1. Can they handle very high tonnage rates?
  2. Are they suitable for continuous operation 24/7?
  3. Can they handle large, heavy, primary crushed ore and waste rock?

The various installations answer these concerns.

Of these, the most important concern is third on the lists.  The answer is that – large belts can handle large lumps, small belts can handle small lumps.

Figure 2 shows a comparison of sandwich belt cross-sections for widely varying belt widths.  Clearly “large” lump size is relative.  350mm lumps are too large to handle at a sandwich belt of 1000 mm width, but not at a sandwich belt of 2600 mm width.  Indeed, to have compatibility of belt width and material size we limit the material size with regards to the trough depth.  For predominantly lumpy material we limit the lump size to the depth of the trough.  For occasionally lumpy material, less than 10% large lumps, we increase the size criteria to 125% of the trough depth.  This is to limit the separation of the belts, preserving a good covering of the bulk material and positive contact at the edges of the sandwich.

Sandwich belt high angle conveyors can and have conveyed very large oversize material from the sandwich entrance to the discharge.  At a muck handling system a 150 HP TBM cutter motor was unintentionally but successfully conveying from loading point to the discharge.  There was some very minor damage, but the system continued to operate until a scheduled down time to make the minor repairs.  It is not a question of what is the largest material that can be handled.  The Dos Santos criteria are to determine the material size that should be handled for reliable, trouble free operation with minimal wear and tear.

The only IPCC application to date in a copper mine, shows that the 250mm lumps are easily handled at the 2000 mm wide belts.

Five years after start up, the system proved its worth:

  1. Reducing the truck fleet by 10.
  2. Precluding the need for 4 km of haulage ramps, 3.5 km of which would be of constant ascent.
  3. Saved $12 million USD per year.

Figure 3: UHAC Elevating/Lowering at a 3-Bench Operation

Almost an IPCC application, another sandwich belt high angle conveyor elevates coarse (250 mm minus) gold ore from the primary jaw crusher to the next crushing stage.  It is at the pit perimeter, not in the pit.  Definitely and overreach on the lump size handled, this conveyor suffered some wear and tear consequences but remains in operation today more than 25 years later.

The vital elevating link of a self-unloading ship system, handles a variety of materials including 305 mm minus rock.  The sandwich belt high angle conveyor lifts the material onto a boom conveyor that discharges the bulk cargo to shore.  This system is right at the edge of the maximum lump criteria for occasionally lumpy material <10% lumps.  Design reflected that, the very coarse rock material is one of several commodities transported, and the unloading conveyors don’t operate continuously 24/7, rather there is much none-operating time at sea.  This system replaced a massive apron type elevator that suffered very costly wear and tear.

Depicted in figures 3 and 4 the UHAC (universal high angle conveyor) is a prospective application in Western Australia.  It is designed as the vital link to salvage an existing IPCC system that has proven sluggish due to its dependency on long, low angle conventional conveyors that link the IPCC system to the remote spoiling system.  Operation of the present system proved impractical largely due to the extensive planning required, much non-productive movement, excavation and re-handling and grading work required to accommodate the present low angle link.  Presently the system sits idle awaiting the vital link that will free the rigid interdependency of the in-pit system and the remote spoiling system.

The UHAC promises salvation, providing a compact mobile link, capable of elevating or lowering the primary crushed 350 mm minus waste rock at 8000 t/h.  Designed with the emphasis on versatility the UHAC can operate in either direction (elevating or lowering the material) and at any level from tramming on grade to a 3×12 meter bench operation.  The UHAC offers the vital versatile link for surface spoiling (elevating) or back filling of the mined out pit (lowering).

Clearly Dos Santos Sandwich Belt High Angle Conveyors are suitable for IPCC applications.

  • They can handle very high conveying rates.
  • They are suitable for continuous 24/7 operation.
  • High tonnage requirements are handled by wide belts that can easily handle large, primary crushed material.
  • Conscientious design will ensure long life with minimal maintenance required.

    Figure 4:  UHAC Elevating/Lowering at a 1-Bench Operation and Tramming on Grade

The system is proven commercially now for thirty five years with success in a significant IPCC system more than twenty five years ago.

Despite the compelling economics, mining operations have not taken full advantage of this technology, effectively foregoing a great potential for improved production and profits.  End users have been disappointed by the large IPCC manufacturers who have failed to embrace the gift of a compact, versatile, vital link to any IPCC system.

The industry continues to struggle with the use of conventional conveyor systems of limited flexibility requiring excessive maneuvering time, excessive excavation, fill and re-handling in order to accommodate the low angle limitations.  The current alternative to conveyors is the fall back position of using 300-ton haul trucks at great operating cost.  With such clear evidence of the suitability and benefits of sandwich belt high angle conveyors, it remains frustrating that mine owner and operators continue to explore what is marketed as new innovation, instead of what’s been proven for years.

Open Pit Mine

Large Sandwich belt high angle conveyors are especially suitable for the large volumes of ore and waste rock from open pit mines.

IPCC, OPCC – what’s the difference?

IPCC is the popular acronym for In-Pit Crushing and Conveying.  There is no popular acronym for Out-of-Pit Crushing and Conveying though it is quite more prevalent in the mining industry.  The proper acronym in this case would be OPCC.  In any case, from an equipment standpoint, in principle there are no differences.  The mined product, ore or waste rock, is primary crushed to a conveyable size then it is conveyed to its respective destination, primary ore storage at the plant or waste dump.  Practically, the implementation does differ.

Generally the crusher of the OPCC system is strategically, permanently located.  The crusher of an IPCC system is located in the pit, sitting on the ore body.  It must be moved periodically as the mine expands.  So the crusher must be relocatable or mobile depending on the mine plan.  The in-pit conveying system must likewise be relocatable or mobile.  The high angle conveyor advantage in this case is undeniable.  It offers complete conformance to the mine slopes requiring no special excavation or rehandling and because it offers the shortest distance between the two end points (receiving to discharge) it is compact and more easily made relocatable or mobile.

IPCHAC, OPCHAC

Though to a much lesser extent, Dos Santos Sandwich Belt high angle conveyors have been used as part of IPCC systems and OPCC systems, hence the proposed new acronyms IPCHAC and OPCHAC.  The high angle advantage is greatest in the pit.  The advantage was exploited at the Majdanpek Copper mine in Serbia throughout the 1990s.  The system had significant features including 2000 mm wide belts continuously elevating 250mm coarse ore at 4000 t/h.  The net elevating height was 6 x 15-meter benches – 90 meters.  The total lift was 93.5 meters which included the transfer height at discharge.  The system scaled the benched mine wall at a mere 35.5 degrees without any special excavation to accommodate the system.  The system was a resounding success and fulfilled its technical and economic objectives:

It precluded tripling of the truck fleet

It precluded the need for 4 km of haulage ramps, 3.5 km of which would be at constant ascent

It saved US $ 12 million per year

Despite the resounding success Dos Santos Sandwich Belt high angle conveyors have not again been incorporated into an IPCHAC system though many were installed at OPCHAC systems and underground mines handling the same primary crushed ore and rock product.

It is against this background that we present the study of high angle versus conventional conveying at an Eastern European copper/gold mine.

Study of high angle vs conventional conveying at eastern european copper/gold mine

A study was conducted by Dos Santos International in a copper mine located in a mountainous terrain in eastern Europe.  The mine plan locates the primary ore crusher at the pit perimeter and the processing plant more than 300 meters of elevation above the crusher.  The customer recognized this to be an ideal route for high angle conveying.  To optimize the high angle conveyor system the customer turned to the expertise of Dos Santos International.

Developed copper mine pit with primary ore crusher at lower left and conveyor system leading to the processing plant at the upper left. Waste rock is spoiled into the valley behind the pit.

Table 1:  Design parameters, ore conveying system, primary crusher to stockpile

Material Copper, Gold Ore
Bulk Density 1.75 t/cu-m
Size 250mm minus
Capacity: 1665 t/h
Design Capacity: 1870 t/h

The system is to use a conventional sacrificial conveyor from the crusher to the start of the high angle conveyor system then the high angle conveyor system to the ore stockpile at the plant.

DSI first addressed the issues of belt width and belt speed for the types of conveyors envisioned:

  • Conventional troughed belt sacrificial conveyor
  • Sandwich Belt high angle conveyor with steel cord reinforced belts
  • Sandwich Belt high angle conveyors with multi-ply fabric reinforced belts

Driven by the material size more than by the modest volumetric design rate, DSI chose the appropriate belt widths and belt speeds:

  • 1400 mm BW at 2.0 m/s for the sacrificial conveyor
  • 1800 mm BW at 2.5 m/s for the sandwich belt high angle conveyors with steel cord belts
  • 2000 mm BW at 2.5 m/s for sandwich belt high angle conveyors with fabric belting.

Belting and equipment recommendations followed including 12.7 mm Grade 1 ore carrying covers, CEMA E6 idlers, shaft mounted drive arrangements and VFD starting and load sharing control.  Take-up systems are automatic hydraulic.

First, DSI conceptually designed and specified the conventional sacrificial conveyor and provided a technical and capital cost summary.  From that point came the main purpose of the study – optimizing the high angle conveyor system.

Sacrifical conveyor from primary crusher to high angle conveyor system

At this copper/gold mine, the great advantage of the sandwich belt high angle conveying system is its ability to follow closely the natural topography, requiring minimal earthwork or elevated structure, as there is no limitation in conveying angle.  The overall slope of the high angle path is actually very modest.

The first exercise compared a single flight main high angle conveyor against two multi flight options – a two flight and a three flight system.  The single and two flight systems required steel cord belts for the high belt tensions developed.  Because of the high elastic modulus, this precluded the tight transition curves that are possible with fabric belting.  The large curves could challenge the system’s ability to conform closely to the natural topography.  The results of this comparison showed the three flight system to be most conforming to the topography but also the most expensive.  This is largely owed to the wider and very costly 2000 mm belts required.  The steel cord belt options, because of their larger curves, did require some elevated structure but this was minor compared to the overall length.

Because of the less expensive, lower strength belting and its consequence, the two flight system proved to be slightly less expensive than the single flight system despite the additional terminal equipment.

The work to that point was presented to the customer.  Based on the options presented, despite the minor cost premium, the customer chose the single flight system for its advantages of reduced transfers and location of all major equipment at the terminal ends where easy access for maintenance exists.

For convenience, the previous comparison did not deal with the complications of the material stacking over the stockpile.  All systems also utilized GPS (gently pressed sandwich) pressing rolls over the entire length of the cover belt.  Pursuant to the additional optimization, Dos Santos International first investigated the need for GPS rolls over the full length.  This revealed that they could eliminate about 67% of the GPS rolls without negatively affecting other aspects of the design.  DSI adjusted the design accordingly, then proceeded to the stacking system optimization.

DSI first considered four stacking variations, but quickly reduced these to two – taking the main high angle conveyor directly to discharge over the stockpile or taking the main high angle conveyor only to the pile base, there discharging onto a separate high angle stacker that delivers the material up to the stockpile.  In order to keep the drives at grade level, the former required additional high tension pulleys at each belt.  These, along with their implications, resulted in a more expensive solution, compared to a less expensive version for the latter main high angle conveyor with independent high angle stacker.  Besides the favorable economics, the latter system also may have the advantage of a material escape option if implemented by diverting the material flow to a side stacker.  In this light, the customer chose the latter arrangement, a main high angle conveyor with an independent stacker to the stockpile.  This is depicted in the figure below.

Main high angle conveyor flight with five separate cover belts along the length.

The above combined with the sacrificial conveyor determines the complete conveying system from the primary crusher to the ore stockpile.

We summarize the total system below technically in Table 2.

Table 2:  Technical Summary, Total Conveying System from Primary Crusher to Ore Stockpile

General Sacrificial Conveyor DSI GPS Main Flight DSI GPS Stacker
Drawing W10202-0000 W10202-0010B
Conveyor Flights Sacrificial Conveyor GPS 10B1 GPS 10B2
Material Copper, Gold Ore
Bulk Density 1.75 t/cu-m
Size 250mm minus
Design Rate: 1870 t/h
Belt Width: 1400 mm 1800 mm 2000 mm
Belt Speed: 2.0 m/s 2.5 m/s
Conveying Angle: Varies to 14.5⁰ Varies to 26⁰ 35⁰
Lift: 31640 mm 340527 mm 41963 mm
Length: 229915 mm 1331688 mm 85840 mm
Drive Power:
Calculated: 241 kW 2996 kW 324 kW
Selected Total 315 kw 3300 kW 370 kW
Top Belt:   1650 kW 185 kW
Bottom Belt:   1650 kW 185 kW
Prelim Belt Selection Steel ST 1250 Steel ST 4500 NN 3 x 455 = 1365

The final system consists of the sacrificial conveyor, a main GPS high angle conveyor to the base of the ore stockpile, and an independent GPS high angle stacker.

A final meeting and inspection of the ore conveying path from the crusher location to the ore stockpile location revealed what was expected from the drawings and the path developed.  Thus DSI believes that the Sandwich Belt high angle conveyors system developed will have the favorable technical and economic characteristics that were presented in the study and report.

The customer has agreed and the final high angle conveying system is incorporated as an integral, vital part of the mine plan that will begin soon.

What are our endless conveying methods?

  • Steeply, firmly, gently
  • Curving, vertically and horizontally
  • Efficiently, effectively
  • Elevating and lowering

We count these but a few of the many ways we can convey bulk materials.  Still, Dos Santos International continues to explore and expand the range of materials handling methods like no other in the industry.  DSI remains at the forefront of bulk solids handling.

For more information on these installations and the many others from Dos Santos International .

LEAVE A REPLY

Please enter your comment!
Please enter your name here
Captcha verification failed!
CAPTCHA user score failed. Please contact us!